Tone Man Guitar prewired kits will improve your guitars performance. Notes will open up. Sound will be stronger, tighter with improved clarity. Tone / volume controls are very responsive. Kits are carefully custom hand wired to order using the best quality parts with vintage cloth push back wire like they used back in the 50s and early 60s. You will not find a better product.
Please read the details below.
Special Tone Modification Pickup Selection: Our Vintage 3 Pickup SG Harness is wired with a special modified schematic that gives you the best pickup combination selection for 3 pickups. The standard wiring for 3 humbucker guitar is Bridge / Bridge & Middle / Neck. With our modified set up the Neck & Bridge pickups still operate the same with the 3-way toggle as a standard 2 pickup SG and you can bring blend the middle pickup in just by turning up the middle pickup volume in any of the switch positions. This gives you Bridge / Bridge & Neck / Neck with the ability to blend the middle pickup in any position. This kit has 1 Master Tone and 3 Volume controls.
This Kit Is For:
Gibson or Epiphone SG with 3 pickups, 4 controls and 3 way switch using short shaft pots.
What's In The 59 SG 3 PU Kit:
I personally prefer Bourn's potentiometers over all other brands incuding CTS. I have found them to be smoother, responsive and longer lasting. The very best taper available. One of the highest rated guitar pots on the market. These pots are coarse 18 teeth spline so USA type knobs will not fit without first pinching the top of the split shaft together a little and slowly push the knob on. Epiphone and off shore type knobs will fit fine. We do offer a line of knobs that fit.
**If you are not sure whether your guitar uses short (3/8") or long (3/4") shaft pots please check before ordering. Normally Pre-1977 Gibson Les Paul's, Epiphone's, SG's, Hamer's and PRS's use short shafts. This kit uses Short Shaft Pots. If you have questions feel free to email me. To verify measure the threaded bushing part of shaft only. Short = 3/8 inch Long = 3/4 inch.
Note: If you have an imported guitar (e.g. Japan, China, Epiphone, etc.) you may need to modify the potentiometer holes to 3/8 inch to accommodate the Bourns bushings. Email me with questions.
If you need new knobs we offer a variety of knobs that fit this unit. See our complete list of knobs under Parts Category
Although these harnesses are pre-assembled and tested they do require some soldering to connect the pickups and the output jack. A 25 – 40 watt soldering iron is recommended. Make sure you are comfortable with making these connections or we suggest you take this to a qualified guitar tech to complete the installation. I can not be responsible if you damage a unit.
Each harness is assembled after purchase so my lead time to build your harness before shipping is 5 to 10 business days. I will send you an email once your unit is shipped.
Tone Man Guitar started from my own passion for music, knowledge of electronics and 50+ years of love for the guitar. The great tone from the 50's and 60's guitars is what I try to achieve. I am a one man shop and do all the work my self. I guarantee the best parts and workmanship. I believe in good communication. If you have any questions or need help with your guitar project please send me an email. We Want You To Be 100% Satisfied!
Cheers!,
Gary Standerfer
Tone Man Guitar
Please read the details below.
Special Tone Modification Pickup Selection: Our Vintage 3 Pickup SG Harness is wired with a special modified schematic that gives you the best pickup combination selection for 3 pickups. The standard wiring for 3 humbucker guitar is Bridge / Bridge & Middle / Neck. With our modified set up the Neck & Bridge pickups still operate the same with the 3-way toggle as a standard 2 pickup SG and you can bring blend the middle pickup in just by turning up the middle pickup volume in any of the switch positions. This gives you Bridge / Bridge & Neck / Neck with the ability to blend the middle pickup in any position. This kit has 1 Master Tone and 3 Volume controls.
This Kit Is For:
Gibson or Epiphone SG with 3 pickups, 4 controls and 3 way switch using short shaft pots.
What's In The 59 SG 3 PU Kit:
- Bourns 500K Potentiometers - Short-Split-Shaft, Audio Taper. 1 Master Tone 3 Volume Controls
- Switchcraft 3-Way R Angle Short Toggle switch with black tip.
- Switchcraft 1/4 jack
- K40Y-9 .033uf PIO Vintage Tone Cap
- Gavitt cloth wiring thru out
- Assembly Template Hard Board (All assembled except for final hook up of ¼ inch output jack & Pickups connection)
I personally prefer Bourn's potentiometers over all other brands incuding CTS. I have found them to be smoother, responsive and longer lasting. The very best taper available. One of the highest rated guitar pots on the market. These pots are coarse 18 teeth spline so USA type knobs will not fit without first pinching the top of the split shaft together a little and slowly push the knob on. Epiphone and off shore type knobs will fit fine. We do offer a line of knobs that fit.
**If you are not sure whether your guitar uses short (3/8") or long (3/4") shaft pots please check before ordering. Normally Pre-1977 Gibson Les Paul's, Epiphone's, SG's, Hamer's and PRS's use short shafts. This kit uses Short Shaft Pots. If you have questions feel free to email me. To verify measure the threaded bushing part of shaft only. Short = 3/8 inch Long = 3/4 inch.
Note: If you have an imported guitar (e.g. Japan, China, Epiphone, etc.) you may need to modify the potentiometer holes to 3/8 inch to accommodate the Bourns bushings. Email me with questions.
If you need new knobs we offer a variety of knobs that fit this unit. See our complete list of knobs under Parts Category
Although these harnesses are pre-assembled and tested they do require some soldering to connect the pickups and the output jack. A 25 – 40 watt soldering iron is recommended. Make sure you are comfortable with making these connections or we suggest you take this to a qualified guitar tech to complete the installation. I can not be responsible if you damage a unit.
Each harness is assembled after purchase so my lead time to build your harness before shipping is 5 to 10 business days. I will send you an email once your unit is shipped.
Tone Man Guitar started from my own passion for music, knowledge of electronics and 50+ years of love for the guitar. The great tone from the 50's and 60's guitars is what I try to achieve. I am a one man shop and do all the work my self. I guarantee the best parts and workmanship. I believe in good communication. If you have any questions or need help with your guitar project please send me an email. We Want You To Be 100% Satisfied!
Cheers!,
Gary Standerfer
Tone Man Guitar
